Trusted by Florence property owners for heat pump repair, AC service, furnace maintenance & complete HVAC installation throughout Oregon.
From emergency repair to planned installation, we deliver expert HVAC service across every specialty.
Clean ductwork directly impacts the efficiency of your HVAC system by reducing static pressure and allowing unrestricted airflow to every register. Our technicians inspect for microbial growth, seal access points after service, and verify airflow improvements with anemometer readings post-cleaning.
Seasonal air conditioning maintenance prevents costly mid-summer failures by verifying refrigerant charge, cleaning condenser coils, and testing capacitor microfarad ratings against manufacturer tolerances. A thorough tune-up preserves SEER efficiency and extends compressor lifespan by reducing operational strain.
Whether you are purchasing a home, preparing for seasonal demands, or evaluating replacement options, a thorough HVAC inspection provides actionable data. Technicians measure airflow, test safety controls, assess AFUE and SEER performance, and deliver a written report with prioritized recommendations.
Installing a mini-split system correctly requires precise wall penetration, vacuum-sealed refrigerant lines, and proper electrical isolation between indoor and outdoor units. Our technicians size each zone independently using BTU calculations to ensure consistent temperature control across every room.
Ductwork problems manifest as uneven room temperatures, excessive dust near registers, and HVAC systems that run continuously without satisfying the thermostat. Technicians identify crushed flex runs, separated joints, and deteriorated mastic seals using pressure testing and visual inspection protocols.
Upgrading to a modern heat pump delivers dual-mode heating and cooling from a single system, with top-tier models achieving 10+ HSPF and 20+ SEER2 ratings. Proper installation includes Manual J load calculations, refrigerant line sizing, and electrical panel verification for reliable year-round comfort.
Boiler systems demand specialized knowledge of hydronic circuits, expansion tanks, pressure relief valves, and combustion analysis. Our technicians diagnose issues ranging from kettling and low water pressure to faulty zone valves and circulator pump failures across gas, oil, and electric units.
Scheduling professional furnace maintenance each fall ensures your heating system delivers full BTU output without wasting fuel. Technicians inspect the inducer motor, verify pressure switch operation, calibrate gas valve output, and clean the burner assembly for reliable cold-weather performance.
Mini-split repair demands familiarity with variable-speed compressor technology and manufacturer-specific diagnostic protocols from Mitsubishi, Fujitsu, Daikin, and LG. Technicians trace electrical faults, recharge refrigerant to factory specifications, and replace condensate pumps to restore silent, efficient operation.
A complete HVAC installation addresses every component in the comfort chain, from the air handler and condensing unit to the thermostat and ductwork. Technicians ensure proper airflow, verify refrigerant charge, and test all safety controls before handoff to guarantee reliable, code-compliant operation.
When your AC blows warm air, short cycles, or fails to start, the problem may involve a failed compressor, low refrigerant charge, frozen evaporator coil, or faulty control board. Professional repair identifies the exact fault and restores rated SEER efficiency through precise, manufacturer-guided procedures.
When your heat pump struggles to maintain temperature or runs continuously without reaching setpoint, the problem often traces to refrigerant leaks, failing capacitors, or degraded reversing valves. Skilled technicians restore rated HSPF and SEER performance through systematic component-level troubleshooting.
Upgrading to a smart thermostat enables precise scheduling, remote access, and energy usage reporting that can reduce heating and cooling costs by 10 to 15 percent. Professional installation ensures correct wiring to your HVAC system, including C-wire verification and multi-stage equipment compatibility.
When your heating or cooling system fails unexpectedly, rapid diagnosis is critical to minimizing discomfort and preventing secondary damage like frozen pipes or heat-related illness. Emergency technicians isolate the fault, whether electrical, mechanical, or refrigerant-related, and execute repairs on the spot.
Clogged dryer vents are a leading cause of residential fires, with lint buildup restricting exhaust airflow and causing the dryer to overheat. Professional cleaning removes compacted lint from the full vent run, verifies proper airflow velocity, and inspects the exterior termination for damage.
When a furnace fails on the coldest night of the year or an air conditioner stops during a Oregon heat wave, every hour without climate control matters. KIC Refrigeration understands the urgency — our emergency HVAC crews in Florence carry common replacement parts, refrigerant, and diagnostic equipment on every truck so we can resolve most heating and cooling emergencies in a single visit.
Our technicians select repair strategies specifically suited to the equipment brands found in Florence, OR. Whether it is a failed ignitor on a gas furnace, a locked compressor on a central AC unit, or a refrigerant leak in a heat pump, every KIC Refrigeration emergency response is engineered to restore comfort quickly and prevent the problem from recurring.
The certifications, standards, and commitments that set our HVAC service apart.
If the repair does not solve the problem or the installation does not perform to specification, we come back and make it right at no additional cost. Our guarantee covers workmanship, parts, and system performance because half-finished work is not in our vocabulary.
Our technicians live and work in the communities they serve. They understand local building codes, climate demands, utility rebate programs, and the HVAC challenges specific to your area. Local expertise backed by a nationwide service network means fast response and consistent quality everywhere.
You receive a written estimate with itemized parts and labor costs before any work begins, and the final invoice matches. No diagnostic fees hidden in the repair bill, no surprise surcharges — just honest pricing you can verify and trust.
Most service calls are completed the same day you call. Our trucks are stocked with over 200 common parts — capacitors, contactors, ignitors, flame sensors, motors, and control boards — so we resolve the majority of repairs in a single visit without waiting on parts.
We carry full general liability and workers compensation coverage on every job. Our HVAC license is current in every state we operate, and we pull permits when local codes require them. Your property and our crew are fully protected on every visit.
Answers to the heating and cooling questions our customers ask most often.
The ideal time for HVAC replacement in Florence is during the shoulder seasons — spring and fall — when demand is lower, equipment availability is highest, and scheduling is more flexible. Contractors are less booked during these periods, which means faster installation timelines and potentially more competitive pricing. You are also more likely to find manufacturer rebates, utility incentive programs, and promotional financing during off-peak months. From a technical standpoint, moderate temperatures allow your new system to be commissioned and tested under less extreme conditions. However, KIC Refrigeration completes HVAC installations year-round in Oregon and can often start within days of your approved estimate, even during peak summer or winter demand. If your current system is showing signs of failure, do not wait for the perfect season — a planned replacement is always better than an emergency one.
Absolutely. Modern high-efficiency HVAC equipment can reduce heating and cooling costs by 20 to 40 percent compared to systems installed 15 or more years ago. The improvement comes from advances in compressor technology, variable-speed motors, and smarter controls. In Florence, upgrading from a 10-SEER air conditioner to a 16-SEER2 or higher unit delivers substantial monthly savings — the higher the SEER2 rating, the less electricity consumed per BTU of cooling. On the heating side, replacing an 80-percent AFUE furnace with a 96-percent modulating furnace means that 16 cents of every heating dollar previously wasted up the flue now heats your home. Heat pumps offer even greater efficiency, delivering 2 to 4 times more heating energy than they consume in electricity. KIC Refrigeration calculates projected energy savings for any equipment upgrade so you can see the return on investment before making a decision.
KIC Refrigeration installs and services all major HVAC equipment manufacturers in Florence including Carrier, Lennox, Trane, Daikin, Goodman, Rheem, York, Bryant, American Standard, Mitsubishi, and Fujitsu. For ductless mini split systems, we specialize in Mitsubishi, Daikin, and Fujitsu units which are the market leaders in inverter-driven technology. We are not locked into a single manufacturer or distributor, which means our recommendations are based entirely on what best fits your home size, budget, efficiency goals, and existing infrastructure. Each brand offers different warranty structures, SEER2 ratings, and feature sets — from basic single-stage units to premium variable-speed communicating systems. Our NATE-certified technicians install every unit strictly to manufacturer specifications and register all warranties on your behalf.
A comprehensive HVAC inspection from KIC Refrigeration in Florence covers every critical component of your heating and cooling system. Our NATE-certified technician evaluates the heat exchanger for cracks using a combustion analyzer, checks thermostat calibration and wiring, tests all electrical connections for tightness and amperage draw, measures refrigerant pressures against manufacturer specifications, clears the condensate drain line, inspects the blower motor and fan assembly for wear, checks the air filter and evaporator coil condition, tests safety controls including high-limit switches and flame sensors, performs carbon monoxide testing on gas-burning equipment, and measures supply and return airflow temperatures to verify the system is producing its rated BTU output. We also visually inspect accessible ductwork for leaks, damage, and insulation condition. You receive a written report with all findings, photos of any concerns, and prioritized recommendations.
We recommend professional HVAC maintenance at least twice per year for Florence homeowners — once in spring to prepare your cooling system and once in fall to prepare your heating system. Each tune-up includes a comprehensive multi-point inspection covering filter replacement, refrigerant level verification, electrical connection tightening, thermostat calibration, condensate drain clearing, and performance testing. For the heating check, technicians also inspect the heat exchanger for cracks, test safety switches, and verify gas pressure on furnaces and boilers. Routine maintenance catches small problems — like a failing capacitor or a dirty flame sensor — before they cause complete system failures. Industry data shows that well-maintained HVAC systems last 15 to 20 years compared to 10 to 12 years for neglected equipment, and they operate 15 to 25 percent more efficiently throughout their lifespan.
As a guideline for Florence homeowners, consider replacement when your system is 15 to 20 years old, when the repair cost exceeds 50 percent of a new system, when the equipment uses R-22 refrigerant which is no longer manufactured and costs $100 or more per pound, or when your system runs constantly without adequately heating or cooling your home. Additional indicators include frequent breakdowns — more than two per heating or cooling season — rising utility bills despite regular maintenance, uneven temperatures between rooms, and excessive noise or dust. The age thresholds vary by equipment type: air conditioners and heat pumps typically last 15 to 20 years, furnaces 20 to 25 years, and boilers 25 to 30 years. KIC Refrigeration provides honest repair-versus-replace assessments at every service call, including side-by-side cost projections for both options.
Real feedback from homeowners and property managers who trust us with their comfort.
"AC tune-up before summer. Technician was early, finished in about forty-five minutes, and gave me a clean bill of health on the system. Easy process."
"Furnace tune-up was straightforward and the technician was friendly. Gave some tips on filter replacement schedules which was helpful."
"Good experience with the furnace tune-up. Technician was thorough and pointed out a couple things to watch for. Only reason for four stars is scheduling took a few days."
Professional heating and cooling services extending to neighboring cities and towns.